A metal part with several holes may look straightforward on a drawing. In the workshop, however, the order of machining can make a noticeable difference to the finished result. A hole drilled in the wrong stage may end up too close to an edge after milling. A deep pocket cut too early can leave the workpiece difficult to clamp. Even a small change in the way a part is positioned can affect the relationship between its holes and mounting surfaces.
These problems are not always caused by poor machining. Sometimes the issue starts before the machine is switched on, when the operation sequence is planned without considering what the part will look like after each cut.
Milling a metal component with holes calls for a balance between material removal, workpiece support, tool access, and dimensional requirements. Some holes can be machined relatively early. Others are better left until the main surfaces have reached their intended shape. The right choice depends on the part itself rather than a fixed order that can be applied to every job.
Check the Drawing Before Setting Up the Machine
The first task is to look at how the finished part is supposed to fit and function. A drawing may show several holes, a recessed area, and a series of milled faces, but not every feature has the same role.
Take a mounting plate as an example. Its broad face may sit against another component, while the holes provide space for fasteners. If the hole positions are measured from the finished edge, that edge needs to be treated as an important reference during machining. Drilling from an unfinished edge can create extra work later, particularly if the edge still needs a substantial cut.
A different part may contain a hole for a locating pin. In that case, the hole position could be more important than the appearance of the surrounding surface. The machining plan should reflect that difference.
Before choosing the sequence, check the following points:
- Which face will locate the part during machining or assembly?
- Are the hole positions measured from finished edges or other reference surfaces?
- Will any pocket or slot leave a thin section behind?
- Can the part remain securely clamped after material has been removed?
- Which surfaces and holes need a final finishing operation?
- Can the important dimensions be checked without moving the part repeatedly?
These questions help establish what needs to happen first and what can wait. They also make it easier to spot problems that might otherwise appear only after several operations have been completed.
Machine the Reference Faces First
Raw metal stock rarely arrives ready for accurate positioning. Its faces may be uneven, its edges may be rough, and its dimensions may leave little room for repeatable clamping. Initial milling is often used to create the surfaces that will guide the rest of the job.
For a rectangular block, the operator might first machine one broad face and then prepare a side face at a suitable angle to it. These surfaces provide a more dependable way to position the workpiece for later cuts.
The same idea applies to a plate with holes near its edges. If the holes must maintain a defined distance from one finished side, machining that side before drilling can make the relationship easier to control.
There is no need to bring every surface to its final dimension at this stage. The immediate goal is to establish reliable references without removing material that may still be needed for support or later finishing.
It is also worth paying attention to how much material is taken off each face. When a part has uneven stock or internal stress, removing a large amount from one side may cause it to move slightly. A surface that was flat during the first setup may no longer remain exactly the same after more material has been removed.
For parts where this is a concern, the operator may need to distribute material removal across several stages rather than finish one side completely at the beginning.
Rough Out the Main Shape While the Part Is Rigid
Once the locating surfaces are ready, the larger features can usually be machined. These may include broad steps, recesses, pockets, and external profiles.
Rough milling is intended to remove excess material, not to produce every finished surface immediately. Leaving a small amount of material for later finishing gives the operator room to correct the final size and surface condition after the heavier cuts are complete.
Workpiece stiffness is particularly important here. A solid block can resist cutting forces reasonably well, but a deep pocket may leave only a thin floor and narrow walls. Those remaining sections can move under the pressure of the cutting tool or the clamping arrangement.
Imagine a component with a large recessed area and several holes around the outside. If the pocket is machined too deeply before the outer shape and clamping plan have been considered, the part may become harder to hold securely. Later cuts could then produce vibration, uneven surfaces, or dimensional changes.
A more considered approach is to decide which areas need to remain solid until the other operations are finished.
A typical roughing plan may include:
- Preparing the main locating faces.
- Removing excess stock from the larger surfaces.
- Milling major steps and pockets while the workpiece still has adequate support.
- Completing external profiles when they will not interfere with clamping.
- Leaving finishing allowance on surfaces that control the final dimensions.
This order is only a starting point. Some parts need an opening or a hole earlier because it helps locate the workpiece for another operation. The important point is to avoid weakening the part before there is a clear plan for holding it.
| Part condition | Possible machining approach | What needs attention |
|---|---|---|
| Uneven raw faces | Prepare locating faces before dependent operations | Consistent positioning |
| Large pockets or recesses | Remove material in stages | Remaining wall and floor stiffness |
| Holes close to a finished edge | Finish the relevant reference edge first | Hole-to-edge distance |
| Thin sections | Delay cuts that would remove necessary support | Deflection and clamping pressure |
| Features on several faces | Plan each setup around common references | Positioning errors between setups |
Choose the Right Stage for Drilling
One of the most common planning questions is whether to drill the holes before or after milling the main shape. Neither option is automatically correct.
If a hole is located from a surface that has not yet been finished, drilling too early may cause trouble. The hole could be correctly positioned relative to the unfinished surface but no longer have the required relationship to the final edge after that edge is milled.
On the other hand, drilling every hole at the very end is not always practical. Some holes may be needed to locate the part, provide access for another operation, or allow related features to be machined in the same setup.
It helps to consider the purpose of each hole rather than treating all holes as identical features.
Clearance holes allow fasteners to pass through a component. Their positions still need to meet the drawing requirements, but their finishing needs may be relatively simple.
Threaded holes require attention to the final hole size and thread condition. If later machining produces chips or sharp edges nearby, the threads may need protection during handling and finishing.
Locating holes position a component or help align it with another part. Their relationship to the reference faces can be more important than the ease of drilling them.
Functional holes may receive pins, shafts, or other components. Their size, alignment, and surface condition depend on the role they play in the assembly.
The intended use of the hole should guide the decision. A simple clearance hole in a non-critical area may be suitable for an intermediate operation. A hole that determines the position of another component may need to be machined after the relevant references and surrounding geometry have been established.
Keep Hole Locations Consistent With Finished Surfaces
A hole can have the correct diameter and still be in the wrong place relative to the finished part. This often becomes apparent when the distance between a hole and a face is checked during inspection.
Consider a metal plate with mounting holes near one long edge. The drawing specifies the distance from the finished edge to the hole centers, but the raw edge still contains material that must be removed.
If the holes are drilled first, the final edge position will depend on how much material is removed afterward. Even when the drilling operation itself is accurate, the finished distance may not meet the drawing requirement.
Machining the edge first gives the operator a known reference from which to position the holes. The same principle applies to end faces, shoulders, and other surfaces used to define feature locations.
There are exceptions. A hole may need to be machined early because a later operation uses it for locating. If so, the process needs a reliable method for establishing its position and checking the resulting relationship with the finished surfaces.
When planning the sequence, it is useful to ask one simple question: Which finished feature is the hole supposed to be measured from?
That answer often clarifies whether the hole should be drilled before or after a particular milling operation.

Plan Clamping and Tool Access Together
A machining sequence may look sensible on paper but become awkward when the operator tries to clamp the workpiece. Clamps can block the tool path, prevent access to a hole, or force the part to be repositioned before a related feature can be completed.
The problem can become more serious as material is removed. A clamp that held a solid block securely may be unsuitable after a pocket has reduced the available contact area. The part may then need additional support or a different fixture arrangement.
For example, a hole near the edge of a plate may be easy to drill in the first setup. A later milling cut may need to pass through the same area, requiring the clamp to move. If the part is repositioned without a clear reference method, the relationship between that hole and the new cut can become harder to maintain.
Before starting a job, consider the entire sequence rather than only the next operation.
- Check whether clamps will obstruct drilling or milling tools.
- Identify which surfaces will remain available for locating the part.
- Make sure thin areas will not be squeezed or distorted by excessive clamping force.
- Decide how the workpiece will be supported after deep pockets are machined.
- Group related operations when they can be completed safely in the same setup.
Keeping related features in one setup can reduce handling and repositioning. However, it is not worth forcing several operations into one setup if doing so makes the part unstable or prevents proper tool access.
A small amount of planning before machining can save considerable adjustment work later.
Leave Final Finishing Until the Main Cuts Are Complete
After rough milling, the part may still need its faces brought to size, its edges cleaned up, and certain holes finished. These operations are easier to plan when the larger material-removal work is already complete.
Heavy cuts can change the way a workpiece sits in its fixture. They may also release internal stress or reduce the stiffness of a section. If a critical surface is finished too early, later operations can affect its condition.
For this reason, it is often sensible to leave a suitable finishing allowance on important faces and complete the final cuts after the surrounding geometry has been established.
The same reasoning applies to holes that require a finished diameter. Depending on the part, the final sizing operation may be delayed until nearby machining is complete. This helps reduce the chance that later work will affect a feature that has already reached its required condition.
Finishing does not mean applying the same treatment everywhere. A surface that simply provides clearance may not need the same attention as a mounting face or a surface that supports a rotating component.
The drawing should determine which areas need careful finishing and which only require the removal of sharp edges or loose burrs.
Hole openings deserve particular attention. Burrs left by drilling or milling can interfere with assembly, affect measurements, or damage adjacent parts during installation. Deburring should therefore be included in the planned process rather than treated as an optional cleanup task.
Inspect Features Before Moving to the Next Stage
Inspection is not something that needs to wait until the part is completely finished. Checking selected features during machining can reveal problems while there is still an opportunity to correct them.
After preparing the reference faces, for example, the operator can check whether they provide the intended locating arrangement. After drilling critical holes, their positions can be checked before later operations make the setup more complicated.
The final inspection should cover the features that matter to the part's function, including:
- Hole diameter and depth where specified.
- Distance between hole centers.
- Position relative to the designated reference faces.
- Alignment between holes on different surfaces.
- Flatness or other required conditions of mounting faces.
- Burrs and damage around finished openings.
The drawing should determine the measuring method and acceptance requirements. A hole used for a loose fastener connection does not necessarily need the same inspection attention as a hole that locates a shaft or pin.
When a measurement falls outside the required range, reviewing the operation sequence can help narrow down the cause. The problem may have started with an unreliable reference surface, a change of setup, excessive cutting force, or movement of the workpiece after material removal.
Checking features at suitable stages also reduces the risk of discovering a problem only after the part has passed through every operation.
Avoid Common Mistakes in the Machining Sequence
Many machining problems develop because each operation is planned separately. The operator may complete a cut successfully without considering how it affects the next setup or the features that remain.
Several mistakes are worth watching for.
Drilling from an unfinished reference. If the hole position depends on a face that still needs substantial milling, the final relationship may change. Establish the relevant reference before drilling when the drawing requires it.
Removing too much material too early. Deep pockets and narrow walls can leave a part difficult to support. Keep enough material in place to maintain rigidity wherever the design allows.
Finishing critical features before heavy cutting is complete. Later operations may affect the condition of finished surfaces or holes. Decide which features need to remain unfinished until the main material removal is over.
Repositioning the workpiece without a clear reference. Every new setup introduces another opportunity for error. Use a consistent locating method and check critical relationships after repositioning.
Ignoring burrs around holes. Burrs can cause assembly difficulties and interfere with inspection. Include deburring and edge checks in the production plan.
Using the same sequence for every type of hole. Clearance holes, threaded holes, and locating holes serve different purposes. Their machining stages should reflect those differences.
These issues are easier to prevent during planning than to correct after the part has been completed.
Build the Sequence Around the Finished Part
There is no universal machining order for every metal part with holes. A flat plate with a few mounting holes may need only a straightforward sequence of facing, edge milling, drilling, and finishing. A block with deep pockets, thin walls, and holes on several faces may require staged material removal and multiple carefully planned setups.
The general approach is to establish reliable reference surfaces, remove bulk material while the workpiece remains adequately supported, and machine critical holes in relation to the surfaces that define their positions. Final finishing and inspection should then focus on the dimensions and features that matter to assembly and use.
Before choosing the order, consider what each operation changes. Does it remove a reference surface? Does it weaken the part? Will it make clamping more difficult? Could it affect the position or condition of a hole that has already been finished?
Answering these questions gives the machinist a practical basis for deciding what should happen first and what should wait. The aim is not to follow a rigid recipe, but to keep each operation compatible with the next while maintaining control over the finished part.